install easily. connect securely. manage remotely.

What is the easiest way to get started with the Junxion Box?

This quick start guide provides helpful pointers that most users will need for a basic configuration.

 

  1. Insert your data card into the Junxion Box.

  2. Power up the Junxion Box. Wait two minutes for the Junxion Box to initialize. The status light should be solid red.

  3. Connect your computer to the Junxion Box using the supplied crossover Ethernet cable.

For advanced configurations (or if you are using a carrier other than Sprint, Cingular, or Verizon) the Device Manager can be accessed with a web browser at 192.168.2.1/admin. The default username is 'admin' and the password is 'junxion'. Refer to your User Guide or visit www.junxion.com/support for further assistance.

 

Can I swap cellular modem cards?

The Junxion Box allows users to swap cellular modem cards in order to upgrade to a faster data network or switch data services. Beginning with Junxion Platform firmware v1.4, the Junxion Box can automatically detect and configure most data cards, making swapping even easier.

Before swapping cards, either power down the Junxion Box or make sure that the card is properly disconnected from the Junxion Box.

To swap cards with a basic configuration (firmware v1.4 or later):

  1. Verify in the Device Manager that the Junxion Box PC Card Modem option is set to 'Automatically Detected'.

  2. Unplug the Junxion Box. This will power down the Junxion Box and the card in a safe manner.

  3. Swap cellular modem cards.

  4. Plug in the Junxion Box.

For advanced card swapping (custom configurations or firmware before v1.4):

  1. Open the WAN page of the Junxion Box Device Manager. In the PC Card Modem drop-down box, select 'My Card Not Listed' and click on Apply. This will disconnect the data card from the WAN.

  2. Swap cellular modem cards.

  3. Open the WAN page of the Junxion Box Device Manager. In the PC Card Modem drop-down box, select the new card, enter any additional configuration information, and click on Apply.

The Junxion Box will restart and attempt to connect to the WAN network.

How do I go about updating my firmware?

To update your firmware, carefully follow these tips to help ensure a trouble-free experience.

  1. Thouroughly read and follow the firmware update instructions.

  2. Write down any custom settings before your Junxion Box is reset to factory defaults.

  3. Take the data card out of the Junxion Box before starting the firmware update.

  4. Set your Junxion Box to factory defaults. You can do this from the Update page of the Junxion Box Device Manager.

  5. When the update is finished, unplug and plug in the Junxion Box to fully reset it.

  6. If you have a Mac computer, the update may take longer than expected. Do not disconnect the Junxion Box during the update process.

  7. If you are using Internet Explorer, you may need to add the Junxion Box Device Manager to the Trusted Sites Zone.

 

What does a blinking red status light mean?

The red 'status' light indicates the connection status. There are three modes:

Solid status light: the Junxion Box is successfully connected to the Internet.

Blinking status light: the Junxion Box does not recognize the cellular PC Card modem or cannot connect to a cellular network. Check the status and settings in the Device Manager to troubleshoot. (Note that the status light also blinks briefly during the boot-up process.)

No status light: the device has just been turned on and is powering up (takes about two minutes).

Can I disable the SSID broadcast on my Junxion Box?

No. The SSID broadcast cannot be disabled.

What cellular modem cards does the Junxion Box support?

Currently, the Junxion Box supports the following cellular carriers and PC Card modems.

Alltel

  • Kyocera KPC 650 (1xRTT and 1xEV-DO)
  • Sierra Wireless AirCard 555 (1xRTT)

Cingular Wireless (including AT&T)

  • Novatel Wireless Merlin U520 (UMTS) and U730 (EDGE/HSDPA)
  • Option Wireless GlobeTrotter GT MAX (EDGE/HSDPA) and GT MAX 3.6 (EDGE/HSDPA/GPRS)
  • Sierra Wireless AirCard 775 (EDGE), AirCard 860 (EDGE and limited HSDPA), and AirCard 875 (EDGE/HSDPA/GPRS)
  • Sony Ericsson GC82 and GC83 (EDGE)

Sprint

  • Novatel Wireless Merlin C201 (1xRTT), S620 (1xRTT and 1xEV-DO), and S720 (1xRTT and 1xEV-DO Rev A.)
  • Sierra Wireless AirCard 550 (1xRTT), AirCard 580 (1xRTT and 1xEV-DO), and AirCard 595 (1xEV-DO Rev. A/1xRTT)
  • Pantech PX-500 (1xEV-DO Rev. A/1xRTT)
  • UTStarcom/Audiovox PC5740 (1xRTT and 1xEV-DO)

Verizon Wireless

  • Audiovox PC3220 (1xRTT) and PC5220 (1xRTT and 1xEV-DO)
  • UTStarcom/Audiovox PC5740 (1xRTT and 1xEV-DO)
  • Kyocera KPC 650 (1xRTT and 1xEV-DO)
  • Novatel Wireless Merlin V620 (1xRTT and 1xEV-DO)
  • Sierra Wireless AirCard 555 (1xRTT) and 580 (1xRTT and 1xEV-DO)

 

How do I reset my Junxion Box to factory defaults?

here are two different ways to reset your unit to factory defaults:

  1. You can use the Device Manager to reset the Junxion Box to factory defaults without powering off the unit.

    • First access the Device Manager by entering 192.168.2.1/admin (or the custom IP address you've configured for the Junxion Box LAN) into the address field of your browser. The default username is 'admin' and the password is 'junxion' unless you have already changed the password.

    • To reset your Junxion Box settings, go to the Update Page and select the Factory Defaults Reset. This resets all of your settings (passwords, LAN and WAN configuration, security settings, splash page, etc.) to the original factory settings.

  2. If you forget your device manager password or are unable to access the Device Manager, you can reset the Junxion Box during the boot process.

    • Restart the Junxion Box by pressing the power cycle switch or removing then re-inserting the power cable.

    • After one to two minutes, the status light will begin to blink rapidly.

    • Unplug the Junxion Box while the status light is rapidly blinking to reset all configuration settings back to factory defaults.

    Note. This procedure works only if the Factory Default Reset Option At Boot option is on. You'll find this option in the Update page; it's on by default.

 

How do I find out if new firmware updates are available?

To check for new updates, go to the Update page in the Device Manager. If the Junxion Box is connected to the Internet, clicking Check Version will provide information about the latest update available from Junxion's web site.

To be notified by email when new updates are available, visit www.junxion.com/support and sign up for Junxion news at the bottom.

What is a cellular router?

A cellular router is a network gateway device that provides, manages, and secures Internet connectivity for local area networks using cellular data services.

Does the Junxion Box have a firewall?

Yes, the Junxion Box contains an advanced stateful firewall. Packet filtering in the Junxion Box is achieved using the netfilter/iptables hooks available in the Linux kernel as a standard part of all modern distributions. NAT, port forwading, port restriction, and MAC filtering are all examples of services provided by the Junxion Box firewall.

If you require extended functionality in the Junxion Box firewall please send a feature request to ideas@junxion.com or contact Junxion support.